Shenzhen Longyuan Lock Industry Co., Ltd.
Banner

Company: Shenzhen Longyuan Lock Industry Co., Ltd. Contact: Ouyang Fa 13534005361

Contact: Jiang Jie 13632655852

Contact: 阮会普13631694748
Fixed line: 0755-33868508
Email: 758047836@qq.com
Website: www.szlysysy.com
Factory Address: No. 317, Huaying Road, Dalang Street, Longhua New District, Shenzhen

Express lock
Express lock



First, the instructions for use:

1. The express cabinet lock is mainly installed inside the equipment, in a waterproof environment.                

2. The product must not be exposed to water, oil and organic solutions.

3. The product assembly is fixed with a suitable torque to avoid excessive tightening and lead to abnormal fastening.

4. Note that the product uses DC voltage regulator 12V -24V power supply ( can be customized)

Appearance structure description:


Code

name

Remarks

A

Lock body

70.6mmX55.6mm-14mm

B

Door Latch

Mounting hole distance 29mm, flat head M3-6 screw (can be customized)

C

Putt

The open state size of the figure, 14mm maximum compression distance 12mm

D

Outlet hole

Exposed wiring length 200mm

E

Emergency switch inlet

Maximum stroke 10mm

F

Mounting holes

Mounting screws M4-8

Note: All dimensions are in mm
Product parameters:


name

Parameter requirement

Remarks

Rated voltage (V)

12V -24VDC (DC) ± 15%

Rated current (A)

0.8a-3a

Maximum instantaneous operating current

3A±15%

Maximum instantaneous working efficiency

30W

Maximum electromagnet instantaneous pull

>4N

Electromagnet core working stroke

6.5±0.5mm

Plastic material

ABS

Lock body length

Exposed length regular 200mm (0, +40)

Can be customized according to requirements

Lock line sequence and color

1.VCC red line
2.GND black line
3.STATE yellow line
4.SATTE Green Line

1. The blue line requirement of LED-GND is:
Lock open: LED-GND is connected to the GND of the lock
Lock off: LED-GND is disconnected from the GND of the lock
2. The two state line requirements are: the two state lines are shorted when the lock is opened, and the lock starts to open the two state lines.

Operating temperature

-20℃ to +70℃

storage temperature

-25℃ to +75℃

Working relative humidity

10%~95% RH (no condensation)

Storage relative humidity

5%~95% RH (no condensation)

Lock housing size

70.6mmX55.6mm-14mm

for reference only

Warranty

Warranty period 1 year

Testing standards:


Serial number

category

Test items

Decision method standard

Provide a report

2

Lock size symbol drawing requirements

Check tool

Batch per order

3

Every time the power-on test is reset, it cannot be stuck or pulled.

Power detection tooling

Full inspection / no offer

4

product testing

The signal light is unlocked and the lock is off.

Power detection

Full inspection

5

Under normal light source, the visual surface of 500mm is complete and clean, the color of the paint layer is uniform, and there are no obvious defects such as flow marks, chromatic aberration, scratches, blistering, corrosion, rust, etc. The length of the shell should be seen when the shell is scratched ≤ 5mm, scratch surface area should be ≤ 3mm2, scratched film area should be ≤ 10mm2 and length ≤ 15mm, no obvious scratch on the surface of the finished wire

Visual inspection

Full inspection

6

Strut reset is smooth

Manual

Full inspection

7

Part salt spray test

Neutral salt spray test 48H, meets the requirements of 6 or above (spring, torsion spring, upper and lower cover, screw)

Salt spray test machine

Batch per order

8

Neutral salt spray test 48H, meets the requirements of level 5 or above (lock hook, fixing buckle, positioning piece, spring rod)

Salt spray test machine

Batch per order

9

life span test

Spring, torsion spring test 40,000 times, still working normally, no functional failure

Life testing equipment

3 months

10

The electromagnet is tested for 50,000 times. The electromagnet has no burnout, odor, and works normally.

Life testing equipment

3 months

11

Micro switch test 40,000 times, still working normally, no functional failure

Life testing equipment

3 months

12

The whole machine is tested 40,000 times, with wear and no functional failure.

Life testing equipment

3 months

13

Drop test

1 meter, 1.3 meter height, 6-sided 8-angle drop test, deformation, no functional failure

Drop test machine

First time

14

Pull test

Push rod and lock for 300N tensile and shear test without damage

Tensile testing machine

First time

15

Load lock test

The axial direction of the lock is 150N, the lock is smooth, and there is no jam.

Test Equipment

3 months

16

Anti-seismic test

The door is randomly tapped with a hammer by 20 or more, and no shock is generated.

Leather hammer

First inspection

17

High and low temperature test

Perform 8.0~70℃ 8 hours high and low temperature test, power on test, no damage to parts, normal function

High and low temperature testing machine

6 months

18

package

Clear (item number, quantity, quality control PASS)

Visual inspection

Full inspection


Packing standard: 100pcs per case, 50pcs per layer, 2 layers

Previous: No Information

下一条: Letter box lock